Parameters and specifications
Communication protocols: Support a variety of communication protocols, including Modbus RTU, Modbus TCP/IP, ASCII and DF1.
Controller compatibility: Usually compatible with Allen-Bradley ControlLogix controllers, communication is via the controller’s backplane bus.
Interface options: Multiple physical interface options are available, such as RS-232, RS-422, RS-485, and Ethernet interfaces.
Data exchange function: realize data reading, data writing, data processing and other functions, support real-time data transmission and sharing between different devices.
Configuration and monitoring: Equipped with configuration software and monitoring functions for communication parameter configuration, communication status monitoring, and troubleshooting.
Industrial grade design: Durability, stability and the ability to adapt to industrial environments.
Parameters and specifications
Communication protocols: Support a variety of communication protocols, including Modbus RTU/ASCII, DF1, ASCII, DH485, Modbus TCP/IP, EtherNet/IP, etc.
Serial port: Equipped with dual RS232 serial application ports supporting RS232/RS485 and RS422 electrical standards, the baud rate can be configured from 110 baud to 115.2 kbps.
Debugging/Configuration port: With an RJ45 Ethernet port supporting 10/100 base-T transfer speeds, link and active LED indicators, and automatic cross cable detection.
Data memory: Users can define a modular data memory map of up to 10,000 16-bit registers.
Configuration tools: You can use ProSoft Configuration Builder(PCB) and Product Discovery Service (PDS) to configure module operations and parameters.
Size and weight
Weight: Approximately 2KG
Parameters and specifications
Digital input/output channels: there are 4 digital input channels and 4 digital output channels.
Backplane current load: 5 volts DC ±5% Max 1100 MA.
Operating voltage: Input voltage range is 110-240V.
Operating temperature: 32 ° F to 140 ° F (0°C to 60 °C), or -40°C to +85°C.
Storage temperature: -40 ° F to 185 ° F (-40 ° C to 85 ° C), consistent with the low temperature end of the above operating temperature.
Relative humidity: 5% to 95% (non-condensing).
Frequency range: 47-63 Hz.
Output current: 0-5A.
Output voltage: 100A (but please note that this may be an error or misunderstanding here, as usually the output voltage is not expressed in amps (A), may refer to other parameters or there is a clerical error).
Output power: 40W.
Size and weight
Dimensions: The housing dimensions are 120mm x 80mm x 30mm.
Weight: 2.3kg.
Parameters and specifications
Input/Output size: 60/120/240-16-bit integer.
Available data: Supports up to 10,000 words of data.
Client and server connections: Up to 20 client and 20 server connections are supported.
Power requirements: Must be installed with a compatible power supply, backplane current load is 500 MA at 5.1 volts DC.
Data rate: Supports 10/100 Base-T Ethernet data rate.
Operating voltage: Possible operating voltage includes 24V DC, etc
Parameters and specifications
Function: Serves as an input/output module between the PROFIBUS network and the ControlLogix processor, supporting the complete master station specification according to IEC 61158 standards.
Communication protocols: Transport via Class 1 or Class 2 DPV1 services is supported, enabling the processor to easily communicate with slave devices that support the PROFIBUS DPV0/V1 protocol.
Processor and memory: Using high-performance processors and memory, fast data calculation and processing, to meet the needs of complex control algorithms and data processing.
Number of slave stations: Up to 125 slave stations can be connected.
Data transfer: Supports up to 1536 bytes of cyclic input and 1536 bytes of output data.
2. Size and weight
Size: The main machine size is 320×240×150mm.
Weight: Approx. 1.2 kg
1. Parameters
Power consumption: Power consumption of 800VDC is 5mA, and power consumption of 3VDC is 24mA. There is also information that the 5VDC power consumption is 800mA, and the 24VDC power consumption is 3mA, which may vary depending on the specific configuration or version.
Version compatibility: Version 16 or later is required when used with additional directives (AOI/AOC); To use with the provided example ladder diagram program, version 15 or later is required.
Configuration tool: The ProSoft Configuration Builder (PCB) is required to input the configuration of the module.
Number of Modbus connections: Supports up to 30 Modbus clients and 20 Modbus servers.
Network port: Equipped with a single Ethernet communication port that supports 10/100 Mbps transmission rates and is able to detect the use of automatic crossover cables.
Server architecture: Demonstrates greater responsiveness in multi-server architectures, minimizing the impact on other servers when a server suddenly goes offline.
1. Parameters and specifications
Operating voltage: Depending on the application scenario, AN-X2-AB-DHRIO may support a variety of voltage inputs, such as 24VDC, 48VDC, etc.
Operating temperature: Generally supports a wide temperature range, such as -40°C to +85°C or 0°C to 50°C.
Communication interface: Supports a variety of communication interfaces, such as Ethernet and DH+.
Supported protocols: EtherNet/IP, Modbus TCP, DF1, DH485, ASCII, etc.
Data transfer rate: up to 10/100 Mbps.
Maximum number of nodes: Up to 64 DH+ nodes are supported in some configurations.
Power input: 24VDC, 48VDC, 220VAC/DC, etc., depending on the model and configuration.
argument
Operating power supply: Usually 24VDC, but other voltage ranges may be supported.
Input voltage: An input voltage range of 110-240V May be supported in some applications.
Output voltage: There may be multiple output channels, each with different output voltage and current capabilities, for example, the output current can reach 0-5A and the output voltage can reach 100V in some applications
Output power: 40W is mentioned in some applications.
Frequency range: 47-63 Hz.
argument
Voltage: 24V
Current: 100-400A
Memory card slots: 2 (SD card optional)
Panel protection level: 3
Number of server connections: Type 3
PLC type support: PLC2, PLC5, SLC, CLX, CMPLX, MICROLX
Number of client connections: Two type 3 clients are connected and one is not connected
Number of I/O connections: The number of Class 1 I/O connections is 2
Size and weight
Size: Depending on the search results, there are two different size data. One is 117mm x 43mm x 129mm and the other is 4.89 inches x 3.53 inches x 1.75 inches (i.e. 12.4cm x 9.0cm x 4.4cm).
Weight: 0.91kg, but please note that the exact weight may vary depending on the production batch and configuration.
argument
Data transmission rate: up to 10Mbps, ensuring efficient data transmission.
Operating temperature range: from -40℃ to +85℃, suitable for various harsh environments.
Operating voltage range: 9V to 36V DC.
Communication protocols: Support Modbus RTU protocol, and other possible communication protocols such as Modbus ASCII.
Baud rate: Set to 9600 (in the example), but can be adjusted as needed.
Data bit: 8 bits.
Stop bit: 1 bit.
Check method: even check (as the primary station) or no check (as the secondary station).
specification
Interface: RS-485 communication interface for data communication with other devices.
Data block size: Supports three different sizes of data blocks, which can be flexibly configured based on application requirements.
Size and weight
Size: Package/specification is 200mmx40mmx140mm
Number of clients: Up to 30 Modbus clients are supported
Number of Modbus servers: Up to 20 Modbus servers are supported
Communication rate: 10/100 Mbps transmission rate is supported
Power requirements:
The available 5VDC power consumption is 800mA
The power consumption of available 24VDC power supply is 3mA
specification
Compatibility: Especially compatible with Rockwell Automation’s ControlLogix platform
Occupied slot: Occupies a single slot in the ControlLogix chassis
Configuration tool: ProSoft Configuration Builder (PCB) is required to input the configuration of the module
Version requirements: Version 16 or later if used with additional instructions (AOI/AOC); To use with the provided example ladder diagram program, version 15 or later is required
