+3.3 volts DC: 1.0 amp nominal value.
+5 volts DC: 1.2 amps nominal value.
Operating temperature: 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit).
Communication interface:
Contains at least two serial ports, such as an RS-232 port and an RS-485 or RS-486 port.
Other communication protocols may also be supported, such as Modbus RTU slave, SNP, etc.
Measurement Method: Karl Fischer Coulomb (coulometric) method
Display: 4-digit LED digital display
Readout Unit: μgH2O
Electrolysis Current: 0-300mA automatic contro
Measurement Range: 5μg-80mg (H2O)
Sensitivity Threshold: 1μgH2O
Accuracy: ±0.3% for 5μg-1mgH2O (excluding sampling error); ±0.5% for above 1mgH2O
Input voltage: 110V-380V
Current: 1A-30A
Power: 5W-130W
Running speed: 2 Gb/s, which can realize fast data exchange between connected devices
Number of supported nodes: Up to 256 nodes are supported in a network
Operating temperature range: -40℃-+85℃
Relative humidity: 5%-95%
Output signal: voltage output
Automatic bypass function: Automatically bypass defective or disconnected nodes when signal loss or loss of effective synchronization mode is detected
Control power supply: 70-265 VAC, 90-300 VDC control power supply.
Output and protection function: with overload, short circuit and phase loss protection function, can cut off the power supply in time when the motor or circuit is abnormal, to protect equipment and personal safety.
Communication interface: Support RS-232 communication interface, with 9600 baud rate, programmable to 19200 baud rate.
Input voltage: 70-265VAC.
Analog output: 4 to 20mA.
Display: Enhanced display (10Base-T).
Protection level: IP20.
Size: 21.8×22.8x25cm (according to the product label).
Weight: About 7.32 kg.
Model Number: IC754VSI06STD-LH
Brand: GE
Control Principle: Other
Purpose: Automation Control Display
Range: 110-210
Accuracy: 0.2-0.9
Dimensions: 12-50mm
Working Voltage: 220V
Output Frequency: 100kHz
Input Voltage: Typically ranges from 4-20 mA.
Output Voltage: Typically ranges from 0-20mA.
Working Current: Typically ranges from 0-200mA.
Voltage: 24V.
Current: 100-400A.
Weight: Approximately 2KG.
Operating voltage: 24~ 48V DC.
Output frequency: 40~65Hz.
Features: With feeder monitoring, fault detection, protection function, communication interface, intelligent management and other functions.
Size: Standard size, specifically 25*65*32mm.
Weight: About 4.65 kg.
Voltage range: The module supports voltage ranges from 0 to +10 volts or -10 to +10 volts.
Current range: The current range is 0 to 20 MA or 4 to 20 mA.
Backplane current: At 375.3 volts, the backplane requires a rated current of 3 mA.
Isolation voltage: The isolation voltage of the IC695ALG708 module is 2550 volts DC and the duration is 850 seconds.
Output load: The maximum output load is 7 ohms.
Input current : 500mA
Output voltage : 24VDC
Output power : 360W
Input voltage range : 85~264VAC
Maximum output current : 15A
Operating temperature range : -25~70℃
Dimensions : 115mm x 48mm x 150mm
Weight : approx. 1.2kg
processor : 16 bits (say 32-bit RISC processors).
RAM : 128 KB.
flash : 1 MB (say 10 MB user memory).
I/O bus : Supports version 16 and later.
Input voltage : 12-48VDC.
Output voltage : 5VDC.
Output current : Max. 10A.
Dimensions : 170mm x 105mm x 32mm.
About 120g.
processor : indicates a 600MHz Pentium-M processor.
memory : 64MB user memory, 256MB flash memory.
I/O capability : Supports discrete I/O up to 32K bits and analog I/O up to 32K bits.
communication interface : Ethernet, RS-232/RS-485, etc.
Operating temperature : -40°C to +70°C.
Protection level : IP67.
Weight : about 50g.
Dimensions : 85mm x 45mm x 23mm.