Showing 2125–2136 of 3228 results

IS220PVIBH1A

¥4,298.00

argument
Input voltage: DC 24V ~ 75VDC
Max. continuous current: 20A
Output voltage: DC 24V (for some applications, such as vibration monitors)
Input current: For vibration monitors, the input current is 1.5A
Communication interface: Support RS232 communication, RS485 and CAN bus optional
specification
Functions: High reliability DC servo driver, suitable for driving hollow cup DC brushless servo motor, hollow cup DC brush servo motor, etc
Control mode: position control mode, speed control mode and torque control mode
Operation mode: Network command mode, pulse/direction mode, analog signal mode and independent operation mode

SR489-P5-HI-A20-E

¥6,250.00

argument
Phase CT secondary coil: 5 A
Control power supply: The high control power supply is 90-300 volts direct current (VDC) and 70,265 volts alternating current (VAC) at a frequency of 48-62 Hz
Analog output: 4 to 20 mA
Fuse current rating: 2.5A, fuse type is 5x20mm HRC SLO-BLO Littelfuse, fuse type is 215-02.5
specification
Product series: 489 series generator management relay
Type: Generator management relay
Accuracy: Not explicitly mentioned, but GE products generally have a high level of accuracy
Control principle: DCS (Distributed Control System)

IS200JPDFG1A

¥4,158.00

argument
Input voltage: Depending on the search results, the IS200JPDFG1A can operate at 24Vdc or 120Vac.
Number of fuses: There are 18 fuses, each with its own power rating.
Number of plug connectors: 14 plug connectors, including 2-bit plugs (10), 12-bit plugs (2), one 9-bit plug and one 5-bit plug.
Communication interface: System feedback such as DC bus voltage and ground fault detection may be provided via PPDA board, and RS232 interface may be supported.
specification
Function: Used as a power module to allocate DC power to the DC.
Control principle: Used with PLC (Programmable logic controller) system.
System capability: Automatic.
dimension
Overall dimensions: 5 inches deep x 5 inches wide x 6.5 inches long.
Package: Other package sizes may be available, such as 2.6×25.8x24cm

IS200TPROH1C

¥6,235.00

argument
SSI data Bit number: A data value that defines how many bits of a data stream, ranging from 1 to 32.
The most important point (MSB) quantity: defines the first value of the bit position of the data in the data bit stream, ranging from 1 to 32.
Number of SSI clock bits: Set the number of bits that 7264 will read from the SSI sensor per interrogation, ranges from 1 to 32, must be greater than or equal to (most important digit + (number of SSI data bits -1)), the default value is 24 bits.
specification
Rated input: 0 ~ 20 kAac
Rated output: 0 ~ 20 madc, 0 ~ 5 vdc, 4 ~ 20 madc
Accuracy: Level 1.0
Linear range: 0 ~ 120%
Isolated voltage: 5000vdc/1 minute
Auxiliary power supply: +12vdc, ±12vdc, +24vdc
Operating temperature: -20℃ ~ +60℃
Temperature drift: <300ppm/℃

HE700GEN200C

¥4,258.00

argument
I/O Points: 20 universal I/O points that can be configured as digital input, digital output, analog input, or analog output.
Voltage range:
Digital input: 24 VDC
Digital output: 24 VDC
Analog input: 0-10V or ±10V
Analog output: 0-10V or ±10V
Resolution: Input/output simulation: 16 bits
Accuracy: Analog input/output: ±0.1%FS
Scanning time: <2 ms
Power supply voltage: 24 VDC
specification
Product type: Industrial automation control interface module
Size and weight
Dimensions: 90mm x 30mm x 25mm
Weight: 100g

IC698CPE030

¥3,268.00

argument

Processor type: 600 MHz Pentium-M microprocessor.
User memory: 64 MB.
User flash: 64 MB.
Discrete I/O capacity: up to 32K bits.
Analog I/O capacity: up to 32K words.
Internal memory: 128 KB Max.
Communication ports: Two Ethernet communication ports, one RS232 port, one RS485 port, and one station manager port.
Accuracy: +/ -0.10% F.S. (for analog input/output modules).
Response time: 200ms (for analog input/output modules).

IS220PTURH1A

¥4,562.00

argument
Power supply: 220VAC AC.
Power range: from 50W to 3000W.
Communication interface: Support USB, RS232, RS485 and CAN bus communication.
Protocol support: Supports MOTECIAN, MODBUS, and CANOPEN protocols.
Operating system: QNX operating system.
specification
Type: Intelligent servo drive, which is also the main trip package for the main turbine of the Mark VI system.
Function integration: Integrated PLC and motion controller, support ladder diagram programming.
Control mode: Position control mode, speed control mode and current (torque) control mode.
Operation mode: includes network operation mode, pulse/direction mode, analog signal mode and independent programmable mode.
Advanced features: Built-in S-curve and T-curve trajectory planning function, support multi-segment trajectory continuous motion.

IS215ACLEH1A

¥6,205.00

Parameters and specifications
Processor: Uses an 80386EX processor with a speed of 25MHz.
Memory: The maximum user program memory is 32K bytes.
Scan rate: The typical scan rate of a CPU is 0.22 ms /K.
Communication interface: Equipped with a built-in serial port supporting SNP/SNP-X slave protocol and a LAN port supporting multipoint, Ethernet, FIP, Profibus, GBC, GCM and GCM+ option modules.
Power requirements: 670 MA from +5 VDC power supply required.
Function support: Support shift register, override, battery backup clock, PCM/CCM compatibility, periodic subroutine interrupt function, floating point math, RAM and flash storage.

IC698CPE030-GJ

¥4,528.00

Parameters and specifications
Type: GE PLC module, part of the RX7i series.
Processor: The module is equipped with a 600 MHz CPU (central processing unit) and is equipped with a Pentium-M microprocessor.
Memory: 64 MB of user memory and user flash memory.
Communication: Supports communication with I/O and smart options modules via a rack-mounted backplane in the VME64 standard format. It is also equipped with an embedded Ethernet port and a serial port of the SNP slave protocol for communication with other devices.
Power supply: The specific power supply voltage may vary depending on the application, but the general industrial PLC module will support the standard industrial voltage range.
Storage: Includes battery-encapsulated user memory and non-volatile flash memory for data to prevent data loss.

HYDRAN M2

¥4,156.00

Parameters and specifications
Application: Mainly used for transformer monitoring and maintenance.
Functions: Detect internal transformer faults, monitor transformer oil moisture and hydrogen, provide real-time alarm and alarm history.
Technical features:
Optical fiber sensing technology, real-time monitoring of moisture and hydrogen inside the transformer.
RS485, Modbus, DNP3.0 and other communication interfaces, easy to communicate with other devices.
Built-in data storage to store historical data and event records.
Programmable alarm function to set multiple alarm types and alarm levels.
Software upgrade function, upgrade software version at any time.
Input voltage range: 12-48VDC, additional information indicates a voltage of 24V, which may vary by product model or configuration.
Current: 100-400A (This information may be specific to some application scenarios or configurations, as not all descriptions mention the current parameter).
Size and weight
Size: There are two different size information, which may be the difference caused by different models or configurations. One is 260mm x 150mm x 100mm and the other is 170mm x 105mm x 32mm.
Weight: There are also two types of information, one is 2.5kg and the other is about 120g, which may also reflect differences between different models or configurations.

IS220UCSAH1A

¥5,200.00

Parameters and specifications
Processor: Freescale 8349,667 MHz processor.
Operating system: Runs on the QNX operating system.
Power supply specification: Rated voltage is 18~36V DC, power is 12 watts.
Operating temperature: between 0 and 65 degrees Celsius.
Cooling method: Natural cooling, no fan required.
Application level: complies with NFPA Class 1 zone 2 specifications.
Communication interface: including Ethernet interface, serial port, etc., used for data exchange with other devices, control systems or networks.
Size and weight
Dimensions: Height is 34mm (door thickness is 33mm).
Weight: Approximately 0.8KG.

IC698CPE030

¥6,235.00

Parameters and specifications
Processor type: 600MHz Pentium-M microprocessor.
Memory: 64 MB user memory and 64 MB user flash memory, both battery powered.
Boolean execution speed: The Boolean execution speed is 0.069 milliseconds per 1000 Boolean contacts/coils.
I/O capacity: Can accommodate up to 32K bits of discrete I/O and 32K words of analog I/O.
Number of blocks: Up to 512 blocks can be downloaded to this CPU, each with up to 128 KB of memory.
Communication interface:
Two Ethernet communication ports support automatic detection of network transmission speed and can be configured for half-duplex and full-duplex operation modes.
One RS232 port.
One RS485 port.
A station manager port.